Skip to main content

MicroAmplifier Dual Op Amps for Single-Supply Sensors | Texas Instruments

Use the OPA2340 input range, loaded output swing and settling time to evaluate a compact sensor buffer.

How close can the sensor buffer get to a rail?

OPA2340 is a dual rail-to-rail input and output amplifier for single-supply operation. Two channels allow a sensor front end to combine buffering and active filtering in one package.

At the high end of the signal range, check the output swing at the actual load current. The voltage available to an ADC can fall short of the supply even when the amplifier is described as rail-to-rail.

If the output drives a sampling capacitor, evaluate settling during the ADC acquisition window. The RC filter at the converter input changes both the transient load on the op amp and the time needed to reach the target accuracy.

Target Applications

  • Single-supply sensor conditioning

Compare MicroAmplifier™ Variants

Comparison of 4 selected variants from Texas Instruments

ParameterOPA2340EA/2K5G4OPA2340EA/250G4OPA2340EA/2K5OPA2340EA/250
Package / Case8-TSSOP, 8-MSOP (0.118", 3.00mm Width)8-TSSOP, 8-MSOP (0.118", 3.00mm Width)8-TSSOP, 8-MSOP (0.118", 3.00mm Width)VSSOP
Max Operating Temp+ 85 C+ 85 C-85°C
Min Operating Temp- 40 C- 40 C--40°C
Operating Temperature-40°C ~ 125°C-40°C ~ 125°C-40°C ~ 125°C-
Amplifier TypeCMOSCMOSCMOSGENERAL PURPOSE
Architecture--CMOSCMOS
CMRR Common Mode Rejection Ratio92 dB92 dB--
CMRR Typ Db--9292
Current Input Bias0.2 pA0.2 pA0.2 pA-
Current Output Channel50 mA50 mA50 mA-
Current Supply750µA (x2 Channels)750µA (x2 Channels)750µA (x2 Channels)-
Gain Bandwidth Product5.5 MHz5.5 MHz5.5 MHz5.5MHz
Gbw Typ Mhz--5.55.5
Ib Input Bias Current10 pA10 pA--
In Input Noise Current Density0.003 pA/sqrt Hz0.003 pA/sqrt Hz--
Input Bias Current Max Pa--1010
Input Common Mode Headroom to Negative Supply Typ V---0.3-0.3
Input Common Mode Headroom to Positive Supply Typ V--0.30.3
Input TypeRail-to-RailRail-to-Rail--
Iout Typ a--0.050.05
Iq Per Channel Typ Ma--0.750.75
Lifecycle StatusActiveActiveActive-
Moisture SensitiveYesYes--
Number of Channels2 Channel-22
Number of Circuits2222
Offset Drift Typ V C--2.52.5
Operating Supply Current750 uA--750uA
Operating Temperature Range C---40 to 85-40 to 85
Output Current Per Channel50 mA50 mA-50mA
Output Swing Headroom to Negative Supply Typ V--0.010.01
Output Swing Headroom to Positive Supply Typ V---0.01-0.01
Output TypeRail-to-RailRail-to-RailRail-to-Rail-
Package8-VSSOP8-VSSOPVSSOP (DGK)-8VSSOP
PSRR Power Supply Rejection Ratio90.46 dB90.46 dB--
Rail to Rail--In, OutIn, Out
SeriesOPA2340OPA2340-MicroAmplifier™
Slew Rate6V/µs6V/µs6V/µs6V/µs
Slew Rate Typ V S--66
Supplier Device Package8-VSSOP8-VSSOP8-VSSOP-
Supply TypeSingleSingle--
Supply Voltage2.5 V to 5.5 V2.5 V to 5.5 V--
TechnologyCMOSCMOS-CMOS
Thd N at 1 Khz Typ--0.00070.0007
Total Supply Voltage 5 V 5 5 V 10 Max V--5.55.5
Total Supply Voltage 5 V 5 5 V 10 Min V--2.72.7
Unit Weight0.000917 oz0.000917 oz--
Vcm Common Mode VoltageNegative Rail - 0.3 V to Positive Rail + 0.3 VNegative Rail - 0.3 V to Positive Rail + 0.3 V--
Vn at 1 Khz Typ Nv Hz--2525
Voltage Gain Db124 dB124 dB--
Voltage Input Offset150 µV150 µV150 µV-
Voltage Supply Span Max5.5 V5.5 V5.5 V-
Voltage Supply Span Min2.5 V2.5 V2.5 V-
Vos Input Offset Voltage500 uV500 uV--
Vos Offset Voltage at 25 C Max Mv--0.50.5
Request QuoteRequest QuoteRequest QuoteRequest Quote
Selection Guide
📦Package
8-TSSOP, 8-MSOP (0.118", 3.00mm Width)→OPA2340EA/2K5G4OPA2340EA/250G4OPA2340EA/2K5
VSSOP→OPA2340EA/250

Base Numbers

MPN counts describe each base number’s catalog coverage; they are not a series total.

Base NumberDescriptionVariantsAction
OPA2340EAOPA2340EA variants from Texas Instruments2 MPNsView Details

Technical Specifications

How close can the sensor buffer get to a rail?

Example topology
Dual single-supply op amp
Range check
Input common mode and loaded output swing

Frequently Asked Questions

Common technical questions about the MicroAmplifier™ series.

Include the feedback network, following-stage impedance and any other DC path from the amplifier output. Check acquisition transients separately.